MakerBot Print is our newest print-prepration software, which supports native CAD files and STL assemblies,
allows you to interact with all your printers via the Cloud, and many other exciting new features.

Download Now


Ursa (bear) - Fully printable Monster Truck

by tahustvedt May 6, 2017
Download All Files

Thing Apps Enabled

Please Login to Comment

Does this Steeringlink03 works for someone? I love the idea for easy centering of both servos by screw rod, but link falls of the ball joint with every bump. I found no photos, is anyone using it? any help? thanks!

i use my own steering setup however first you should be using any steering setup with a servo saver of some type. having the ball joint connected directly to the servo arm can damage the servo when force is applied to the wheels.
next if the ball joints are popping off easy then you will need to adjust your printer to tighten the tolerances the ball joints should be difficult to pop off and require some reasonable force to pop off. if the joints pop on and off without using a pliers then the tolerance is too loose. you can either shrink the part in slicer a small amount or increase your extrusion multiplier to "fatten" the part up a little.

thanks for reply! the hole for ball is just wrong shape, I guess my first layers are not perfect at the moment with PETG. The ball does not turn in the hole,screws turn instead, and ball joint pops off. I printed one remix of steering links and will try it soon. These servo savers don't work on mine servos yet... I will print servo horn in flexfill 98 or resize savers later. I also bought very good 17g servos by mistake so I will remake design of one part in new axle housings (GB03) from 23mm servos to 28mm servos. Files would help, anyone?

Print the links and balls at 0,08 mm layer height and 0,4 mm width which will give closer to design dimensions. If that's still too tight try -0,05 of horizontal size compensation in Simplify 3D. If you don't have that function in your slicer try resizing the balls to 99%.

I use these links in many cars and even jet planes.

seems to be a problem on behalf of thingiverse - all updated models seem to have the same problem - it takes a few hours or days to generate the according zip-files and thumbnails

Well... nothing has changed :(

yeah thingiverse is having major problems the last year. pages are getting corrupted and parts have been corrupted in some cases as well.

when i click the download link i get the broken page as well.

Well... I don't know if it is specific to my web browser, or if other guys here are this issue: trying to download all files (button download all files) jump to a strange download page without pictures, and the downloadable parts are not those displayed in the main page... Do you have this problem? is it related to the update?

what are the new file changes?

I removed old files that are obsolete.

Nice job. Please keep the best and improved parts and get rid of the old ones.


is there a manual on how to assemble the vehicle after printing the parts?

Thank you very much!

will this body fit a 1/10 rc chassis?

Love this truck actually been driving it for a few months now my kid is obsessed with it so thank you but just a question regarding the drivetrain, which type of drive did you finally stay with. I have been running mine with the original hex style c/v joints but consistently keep stripping them out printed with pla at 0.2res and 100% fill...the gears actually have lasted incredibly well. In fact I'm still running the first spider gears I printed. The main things that fail for me are the hex c/v joints and the gb02 input gear. I guess I'm just curious if the optional pindrive set up is more reliable...thanks for any help and thanks for taking the time to create and share this awesome truck with us

I haven't had a single pin drive fail on me. It's a lot better than the hex drive.

I've had different failures of the pins. the thing about kids is they do things you don't expect and it leads to failures.
when the kids go forward and backwards rapidly they twist the pins they can fall out. on the CVs conversion i've had to make numerous alterations to the design. i incorporated Caps for the pins this required redesigning the axles for more internal space as well as thickening the cases for more stress. i've also beefed up the counter gear as the kids managed to twist the PLA and strip out gears, the countergear is now supported against the gear case under load, the combination of thickening the backside of the gear and supporting it against the case allows it to handle more stress before failing. for the CV conversions you have to use Nylon for all the pivot points you need PLA shafts because of the stiffness of material, nylon or PETG just twists and fails. i recommend making the chassis sides from Nylon as well. all the gear and axle cases from PETG as nylon proved to be too flexable and PLA too brittle when beating on the trucks. each time i let the kids run the trucks they destroy them but i learn from the failure and continue to revise the design. i have a nice cantilever suspension system swapping out the original design allowing additional fun with rock crawling. i have continued to revise the steering mechanicals as well again best is abandoning PLA for PETG because adding a little flex helps keep the kids from destroying that end of things.

Awesome thanks I've started printing the parts thanks again!

Hi, but are the bearings tight or loose? I have too much play I do not understand what it depends on, and then the 3mm rods glued to each other ??

you need to dial in your 3d printer. too loose can be under-extruding, too tight over extruding. there is tolerance given to the bearings so they fit properly but your 3d printer has to be calibrated well. i would run tolerance tests with models from thingiverse then set your extrusion multiplier for the filament you are using

Hi, thank you very much for the support, I checked everything and printed a 30 x 30 cube and it prints very well with the caliber. Size 30.1 so almost perfect, but I used pla, printing with nylon changes something ?? but the 3mm x 19 rods glued to it ?? Or are they just pushed and inserted?

the truck was designed for PLA. Nylon will shrink a lot more. PET-G also will shrink slightly more then PLA. i recommend just a few parts printed from nylon. the small 4 bevel gears in the center and axle diff(12 total), and the 4 wheel axles(inserted into the rims). PET-G would work better for the suspension arms for some collision flexability the rest just PLA with good fusion on the layers. the 3mm rods just slide in no glue.

I like to glue the large bevel gears to the axle shafts so the shafts do not come out of the gear ends.
i recommend changing the dogbone style shafts to CVD style. there are a few remixes on changing the drive shafts.

depending on your gear mesh you might need my 29T lower axle diff replacement gears.

besides cube tests there are also tolerance tests for shapes and round holes to weed out mechanical problems with your printer and slicer settings

The wheel pins, for example, how did you print them in nylon? Have you increased the print flow or the dimensions etc ??

every printer is different and it also depends on your filament and if you are drying it before printing. you will have to test and adjust on your machine.

Hi, so nylon is not good for all gears, so the micro gears of the differential are enough and the pins rotate ?? I printed all in nylon so in doing right I was wrong, you have the gear in pla ?? I have printed them in caRbonfill before and they are broken immediately I attach the photos .. I mounted a 21t engine I have to switch to a less powerful one?

the PLA is strong enough for the larger gears, the bevel gears are very small and right on the edge of a .4mm nozzle being able to print them so nylon will take the higher temps in the smaller area and produce a better bevel gear. the nylon can also take shock loads with out cracking off the gear teeth. you will need to come up with your own formula for printing them on your machine. the small bevel gears should rotate on the shafts so you may need a set of MM drill bits so you can resize the holes for the shafts. i use all steel shafts in my trucks so i have changed the bevel gears from 1.75mm to 2mm shafts. all my large gears are printed in PLA. if the gears fit very loose or skip under load then you need to readjust your printer as the tolerance is too loose and the gears moving around too much. you can compensate by increasing the extrusion multiplier. carbon fill not printed correctly can be brittle. you will need to run tests to see if you are printing too cold or too fast. otherwise go with PLA it is strong when printed correctly. also carbon filament requires a hardened steel nozzle.

Shaft01, large axis size 12.8 smaller axis size 11.8, it will never adapt I have to modify here why

your slicer is seeing the bearing lip on the right shaft.
it works fine.

Can you explain how you fit the pad before the lip? If the measurement is 11.8 the bearing does not fit but is free, to make it fit you can only over-extrude the file is not correct

i don't understand what you are asking. the shafts will be 11.8mm for the bearings which are also just under 12mm
the bearings slip from the outside inward.

The bearing insert it From the side of the wheel towards the inside ?? If you insert them as they fit together if you only fit 11.8, the bearings measure 12mm precisely, the only explanation is that you have an over-extrusion

bearings are usually undersized a 12mm ID bearing usually ends up around 11.90mm the 11.8mm gives a tolerance clearance of .1mm which is the average for Extruder 3d printing. if your bearings are not fitting then usually you have over-extrusion.
the Hex ends will fit with almost zero tolerance into the large bevels so you usually have to hammer them into the axle shafts to seat them.
as is the STL files are all fine except for the amount of clearance between the countergear and the diff gear in the gear case. there is a little debate as the stock placement will skip under load, there have been 3 major revisions to the axles and the design has been altered greatly from how it was 2 years ago. it still works but if you are skipping then you can try my 29T diff gear to take up the extra spacing.
the stock HEX dogbones wear out fast and i recommend the CV conversion for the truck.

https://www.thingiverse.com/thing:2504465 And this? Since it is this: unfortunately I have to reprint the change I will try, mount the same gears cgb02 ??

CV joints for tahustvedt's Ursa (bear) - Fully printable Monster Truck
by zxcvbn

yes the CV system is superior to the hex/dogbone type. you will have much smoother power transfer and steering.

Since you've already tried it, you have the joint balls printed in Pla, in nylon so you have printed the 4 micro gears, the one that goes to the center of the differential and only the screw that serves to hook the right wheel ??

the CV shafts and the center gearbox outputs are PLA the wheel axles CV printed in Nylon. the 4 small bevels all printed in nylon(12 pieces)

you want the nylon where the most shock loads are located. these are the small bevels and the wheel axles. the steering linkage can also be made from nylon if you wish.

if you have to sand the shafts to fit the bearings then you are still over extruding.

now one issue with printing the axle shafts from nylon is the 4mm bolts for the wheels will not fit. you will need to predrill them to except a 4mm tap and use a 4mmx.7mm pitch tap to finish the wheel axle bolt holes. this is because the nylon will shrink compared to PLA.

printing the small bevel gears in nylon will be difficult i recommend, splitting them from the STL then turning them over 180 degrees so the wide base sits on the bed, step out about 12 of them so that you have space between them to cool and prevent over heating(melting) use a raft and a brim to help hold down the small bevels as the white glue will not be enough on the bed even with a PEI sheet on it.
.2mm resolution and you should get good results.

also because of shrink with nylon you will need to drill out the center of the small bevel gears with a drill bit. i recommend 2mm instead of attempting 1.75mm and switching to steel rod 2mm shafts to complete the diffs. they will be much stronger and run smoother.

Hello, I'm sorry but from the translation with Google I didn't understand what you mean, the file axel upright gear etc ... Did you print it in nylon ?? For the wheel axle I had already printed them at 101% resolution and the 4mm screws tightened perfectly

With the cv updateI had to sand to get the bearings in :) however, the pla seems very durable

Comments deleted.

Ok thanks for the tip, I wanted to thank you in another way but it tells me that you have not configured your account

For the aces I will do an over-extrusion, the 29t already tried it but it was too big and it just couldn't turn, I know that the problem is gears because the ones that I mounted could not turn in the steel rods I know that the problem is that, Where do I find the conversion to cv?

Hi, for nylon you are right because it shrinks, but the axes of the shaft01 file do not fit the pad because I believe there is an error, I uploaded the file in Slic3r 3d, the largest size as width 12.8 but the smallest size as width 11.8 so it is not the printer that gets it wrong but it is the file, we have 12 bearings if the file is 11.8 wide it will never fit together, I know that you over-print the printer

I will try to print all the gears with the pla, and the small ones enlarge the holes with a drill bit and try again it may be that it is because the nails I had inserted inside were tightened, the problem of the. Bearings that move there only with the nylon I will print them with pla and I see, then even if I do not even resolve to ban all sincerely very frustrated

Hello, first of great work with the design, loving it so far. Almost have it done and ready to race away. But I'm having an issue with the body3 stl. It slices in a way where it breaks the roll bar mounting holes, and cuts them off half way trough, running it trough a stl fixer makes it a bit better but the full print still comes out a few cm short so it does not reach the rest of the 2 body parts when mounted on the poles. I have it sliced in Simplify3D. The error detection does find some issues with this particular stl. Has anyone here had any similar problems with this file?

no, I just re-downloaded the newest files and put body03.stl into Slic3r and it worked fine no errors.

Comments deleted.

preview looks ok for me as well, but once prited it has issues. I will try to print it with slic3r pe.

This is awesome. I just ordered the bearings, tires, and filiment for this and hope to start printing this weekend. Thank you for providing the split frame for those of us with 150mm printers. I have a few questions:
1) Are all the screws socket head cap screws? ( The ones with hex drive and commonly used in countersunk holes?)
2) What are the approximate lengths of the pins? (I'm thinking about using dowel pins.)
Edit: ahh 7 of 3mm x 19mm and ? of 2mm x ?
3) Should I mirror the (split) frame pieces for left vs right sides before printing or just use one backwards?
Thanks again for this cool project to get me using my printer again and some quality time with my son.

Where did you find tires? And which rims are you using?

Hello, I succeeded, the bearings moved too much, printed only 102% of the width I solved the problem, I printed the wheel pins with nylon but these are small for the bearings, I do not know why maybe the nylon shrinks, , how can I print them? Thanks for the support

The bearings hold up well now, I printed the file shaft01 with a width of 102 and as you can see from the photos hold well, I put a 3.5 mm rod so keeps everything as straight as possible, I'm wrong something from the photos I posted ??

Because of all the problems reported I'm going to print a new complete gearbox to see if I can replicate it.

No problems with the one I printed. Are you guys assembling it correctly? Are you not using the 3x19 mm rods?

as I said I put a 3.5 rod because I increased the size of the file shaft01, the bearings were too wide that was the problem, the assembly is almost impossible to make mistakes, the gears go against each other

Comments deleted.

thanks really, if possible it also indicates the print settings., I use care I do not know if anything changes

You can help me, I have mounted everything but jump the gears, practically sliding both forward and back, if I raise the car seems to work if I put it on the ground does not walk what can it be?

the differential lock is not mandatory right?

No, it eliminates the differential function.

already tried, too big has no room to move, I'm reprinting the axles that keep the crown because they do not fit into the bearings and may be that the crown slips away booo ...

Hello, but the cardan wheels also turn to you a little crooked ?? But I have not yet tightened the screws of the shell GB03 because they must deliver to me may be that once screwed will be fine?

wow man that turned out so good! this is now my next project its so kool i need it lol. great job! how well does it hold up under load has it broken parts yet?

Which servos are you using? The one in the description or another one? Maybe there is a cheaper one, which fits this truck?

  • Posted with 3D Geeks Thingiverse Browser App

the ones in the description: the servos are 12$ each , for a metal gear with a good amount of torque they are already a good deal. they are more expensive on ebay.



Where are the 4 to 8 3x7x3 bearings used and how many should I use? but the model has the steering both forward and back? so I need 2 servos? cmq for the gears I took the pla with carbon fiber I will let you know, if you have more photos of the assembly would be welcome ..

they are used in the upper counter gear the gear that connects the 90 degree bevel to the lower diff gear on the 3mm shaft. you need 4 of them.

yes 2 servos and a Y cable or you need a radio that can be setup for 4ws.

the gears work fine in PLA just the small bevel gears should be made in nylon.

the assembly of the CB03 axles is basically the same as the CB02 you just assemble vertical instead of horizontal. the pics above are enough to figure out how it goes. the axles can only assemble one way. due to the diff off-center placement.

m sorry but I did not understand the 3x7x3 bearings go into the central differential where the engine houses?

I do not know if it's my printer but to me with the noozle from 00.4 to print the frame set to 0.2mm resolution in care gives me problems with the first layer the circles takes them away, while with the noozle from 00.3 mm I'm using I have no problem I'm wrong? I have an ender 3

you will have to look at your slicer settings and possibly adjust your live Z. if you have been printing at .3mm then switched to .2mm then look at your first layer height setting in slicer. typically no matter what your layer height is you have the first layer set to a fixed .2mm height. this is set in the slicer. this keeps the first layer height at the same starting point for all resolutions. my guess is your slicer has the first layer height set to the same number as resolution. so you ran at lets say .3mm height and set your live Z for that. now you have gone to .2mm and the first layer is not being squished the same into the bed to start the print correctly. so increase first layer live Z so you get a good first layer and the rest will follow. keep in mind when you switch back to .3mm you will need to decrease live Z or it will squish too much. if you print at .15mm then you will need to increase live Z again more then you had for .2mm. again you can setup all first layers in slicer to be .2mm for all resolutions then keep the live z the same no matter what the resolution is after the first layer.

Thank you so much for the support, I set the line width to 0.04 having mounted the noozle to 00.4 and the software has calculated everything automatically and then I have obviously set the fill, but the real problem is the glass does not attack well I sprayed the hairspray x hair and the result is powerful

you might want to either go with a PEI bed in place of the glass or kapton tape attached to the glass to increase adhesion.another option is putting the printer in an enclosure to keep the ambient temperature around the part more stable to reduce warp and lifting during the print.
you could also increase bed temperature if you have a heated bed.
i do not use the ender 3 printer so that is about as far and i can tell you to go.

I'm using the bed at 60 and the noozle at 200 and goes wonderful, the glass is borosilicate and has pores to hold the press but most of the time it does not work, now with the spry lacquer it prints very well

Guys, for the press you used noozle to 0.2mm or to 0.4mm ?? I'm a newbie in 3D printing I do not understand what it means to resolution at 0.2mm

most printers use a .4mm wide nozzle. the layer height is variable. .2mm is the height in this case. as it is a lower resolution but creates objects faster. in this case the resolution is 0.2mm which the height of each layer in the Z direction(up down) while .4 is the X/Y left right front and back resolution. the .2mm is the height of each layer. 1mm at .2mm height means the nozzle will move upwards 5 times to complete that 1mm thick part.

So in practice with the noozle at 00.2 mm we only put more time but the result is equal to that from 00.4mm ??

I used the GB03 on the rear axle and I get no friction between the top gear and the diff gear. In front it works, because the direction is changed and the upper gear will be pressed down. On the rear axle the upper gear will be lift up a bit and get no friction.

The car is not running. I reprinted all components and assambled complete new parts, but the truck won't drive.

Have anyone the same problem? What can I do?

The new gear works very well, it perfectly fits. Many thanks for this. Good work.

-Hello, thanks for the opportunity is really exceptional, I can not find the following pieces:

3mmx19mm in fibra di carbonio, alberi in acciaio o ottone per cambi differenziali e asse vivo:
2mm asta in acciaio per alberi di trasmissione a perno e ingranaggi conici diff:
https://www.banggood.com/22mm-250500mm-1_52mm-Thickness-304-Stainless-Steel-Round-Tube-Rod-p-1064909.html?p= HD240528697332015103 da

Where can I find them? Or do you have photos to understand what they are?

these are just shafts you need to support the gears and axles.
they are round solid rods that you need to cut to the correct lengths so they fit into the different area where needed.
you can use 3mm nails where you cut the heads off and then cut the length down as needed you can use 1.75 filament where the 2mm is used. however if you use the filament i would use nylon 1.75mm in place of the PLA nylon properties are higher melt temp a slick surface and it will not fuse to the PLA when it heats up. i would recommend not using the filament and go with the steel shafts as the gearbox will be much stronger.

3mm shaft as example

2mm as example

i also recommend printing the small bevel gears in nylon 910 and the wheel axles in nylon 910. the PLA tends to shatter under the loads and shocks from jumping nylon is much stronger then PLA and will absorb impacts without cracking or breaking.

For the 2mm rod you can use 1.75mm filament, it will only used for the diffs. Usage is documented in pictures on the project. For the 3mm rods I used 3mm x 40mm nails and shortend them. this works very fine.

Currently printing one now, I am using clodbuster tires and rims with a 12mm hex, also using some friction shocks I found in the remixes, should do well in snow and mud.

Seems M3x10 work everywhere but the knuckles. M2x8 worked to hold the main halves of the axle together, but need longer for the input cap (or drill the recesses for the heads deeper).

Great model! Have a growing pile of parts printed and waiting for hardware to come in. Could You post the spur as well as the small diff gears as separate files for easy printing of replacements? Thanks! ~M

your slicer can handle this, there is a split function in most slicers, when you click on it the STL file is split into each of its components. and then you can delete the pieces you do not want.

another option is you can download meshmixer from autodesk which is free, load the STL then click edit and click seperate shells. then you can select the pieces you wish to export back into STL files. this will separate all the little groups of parts.

Thanks, just realized slic3r could do this!

i would recommend printing the small bevels in taulman 910 nylon. PLA doesn't last long because those bevels get a lot of shock loads. PLA is brittle so i tends to chip teeth off. nylon in this area works perfect. i use 910 for the wheel axles as well, if the tire hits something it tends to snap the PLA wheel axle shaft right at the outside bearing face again shock loads with brittle pla. nylon here is flexable and i've never broken a 910 axle.

i also find i get better print quality on the small bevels if it turn them 180 degrees so the larger side is on the bed, then raft the bottom lip and print the gear from fat to thin. the other way around usually requires a brim to keep the gear from popping off the bed and it melts the narrow areas a little too much and makes it harder to clean the gear up after the print is complete.

Thanks for the tips. I'm trying PETG for the gears while I wait for nylon. The little ones are what I had some trouble with, I did use a small brim to keep them down, but the teeth did not come out so great because of the small-perimeter overhangs, I will try flipping them over.

Have filled one filament roll bag up with parts so far, and still have the body to go!

for the nylon run it hot but run like 8 bevels at the same time spread them out a bit. this way it will cool the layers more as the total time per layer will be higher. the nylon will shrink a little but you just need to clean out the center shaft holes with a 2mm drill bit and it will still be ok for 1.75mm filament. although i recommend going with the 2mm steel shafts in place of the filament shafts.

Build's nearing completion, ran it around the house with front steering only and a 23t motor (35t en route). Steering's a little limited because i cut the servo horn too far to clear the bottom link, gonna try flipping the servo in stead to allow for a longer horn, think i'd rather than than move the lower steering link down and attach it to the knuckles from the bottom.

Having a small problem in that the tips of the body posts are not long enough and do not protrude above the hood and bed of the truck body far enough to get some clips in the holes. Anyone fix those yet?

did you use the correct body posts. there is nothing wrong with those STLs.
the body posts for the Big bear body are in body04.stl

the bodypostXX.stl files for for after market lexan shells.

That was it, wrong posts, I didn't even realize they were in Body04. Thanks!

did you use the correct body posts. there is nothing wrong with those STLs.
the body posts for the Big bear body are in body04.stl

the bodypostXX.stl files for for after market lexan shells.

what you mean, is it possible for the rods 3mmx19mm to use threaded screws m3 for the bearings 3x7x3 ???

basically if you are short on materials you can adapt a 3mm bolt. you can chop the head off the bolt and use it as a shaft.
you can also go to the home store and buy some nails that measure out to about 3mm(just under) so you can cut the head and pointy end off and use it as a shaft. you can buy ready made 3mm rods and chop them to size as well. it is also possible to 3d print the shafts.
all these options give you flexibility to help you create the truck however depending on the method for the shafts you have pluses and minuses.

the best option is to purchase some 1mm, 2mm and 3mm shafts they come in handy for different projects. for the ursa bear you will need 2mm and 3mm shafts to create the strongest and tightest drivetrain. 3mm is used on the main shafts and 2mm is used for the small bevel gears and if you decide to convert to CV driveshafts. everything is optional so it will be up to you how far you want to take it.

loose tolerances in the gearbox can cause the gears to skip or become damaged from incorrect meshing under load.

additionally using Nylon in some key areas helps to increase the trucks durability.
PLA is ok but doesn't take shock impacts very well (it cracks)

changing the small bevel gears, steering servo arm parts and the wheel axles to Taulman 910 nylon will remove some weak spots that PLA or PETG can cause.combined with proper 3mm and 2mm shafts and converting to 3d printed CV joints can actually bomb proof the driveline , free up friction and make the truck drive much nicer.

the truck is a really good design that allows for a lot of flexibility Tahustvedt really came up with a winner here. so take it slow take your time do it right and you will be amazed.

Thanks for this detailed answer. I have already bought 3mm rods and I will probably print the parts later in Taulman 910 Nylon.

Maybe, but M3 screws are usually slightly thinner than 3 mm so you might end up with a looser mesh.

Do you have any special instructions for printing the wheels? how many infill?

Do I have to glue the tires on the rims?

it is really going to depend on your TPU and printer.
most of the FLEX TPU is still very stiff even on minimal settings.
ideally you want to have 1 perimeter because that will leave the TPU tire at its softest. however you may not be able to obtain this with your printer.

be aware these tires can take over 40 hours of printing TPU flex has to print extremely slow. so try to dial in your TPU/flex setting before even attempting it.
you also need about 2 spools of TPU as you can print about 3.5 tires before running out of material, if you don't have a filament sensor then you will want to stop after the 3rd print and swap spools.

i never finished a successful set of TPU tires for my usra bear. at 2 perimeters and 5% infill the tires were WAY too stiff and as i experimented with 1 perimeter and 0-2% infill i had top layer issues. the cost well exceeded just buying tires from china so i gave up, but i have about 6 TPU printed tires with different degrees of failure. another reason i stop was the time involved. well over 200 hours.
smaller tires i continued to make for open rc f1 and some other homebrews where the print time was around 12 hours.

it would be faster to make a inverse mold setup from the ursa tire and pour RTV silicon in the mold and create a tire that way.

but back to the tires. you want 1 perimeter if possible and as little infill as can get a away with as it will also stiffen the tire.
the best would be 0% infill then cut the inside center of the tire open and insert a foam doughnut. as for glueing the tires they fit pretty well on the 2 piece rims, however you can just put a couple of dots of CA(crazy glue at 9,12,3, and 6 oclock around the tire and it will be more then enough to hold it.

sorry, i mean the rims and not the tires. i bought the tires and the rims (wheels) i want to print. but i already done with printing

for the rims. you want them strong and having weight as low as possible makes the truck less tippy. so run them at 100% infill with 3 perimeters.

Thank you for this thing! Thumbs up to you!

  • Posted with 3D Geeks Thingiverse Browser App

I have seen that in front and behind each a servo is installed. how are they controlled? separated from each other with one channel each on the remote?

You can control them separately if you want or together. Full scale monster trucks have both the ability to control them together, and separately if needed. If you have an advanced transmitter you can add mixing with different steering modes.If you have a simple transmitter and want to control both at the same time you will need to reverse one servo. Reversing circuits exist for that purpose.

fantastic, thank you... great job.

i have a FlySky FS-GT3C Transmitter

Hi, I'm noobie with RC. It is normal that when I release the throttle the wheels stop. There is no deceleration at all. It's hard for the gears...

Your ESC is set to Active Braking. Google how to connect to your ESC and change that. I believe the software is BLHeli

This is probably a calibration issue. The brake should not engage until you activate it with the stick.

Hi again. Does anyone have the steel rods for the build lying around they want to sell and can send to New Zealand (at my cost) as I can’t find them anywhere. I have 5 of the bigger rods, but need the rest and the small ones. Thanks in advance.

Hi there, Do you happen to have the interior windows for the body without them ? as would like to print in a see through PLA. I also want to make a dash board with steering wheel and driver. Also am just starting the printing process now. Cheers

FYI, clear 3d filament isn't very clear at all. no matter the brand you get a fogged over look where anything an inch away from the material is impossible to make out. so if your expectation is some plastic model clear window that will not happen at all. the design with the windows on the ursa is to use clear plastic sheets and cut them out and glue those in since you really cannot 3d print clear such that it looks as you expect.

the body will also be weaker since the windows are separate pieces, so on roll over it will cause a good amount of damage to the body.

here is an example of 3d printing clear filament using the clearest filament available in 2018. this was after 4 hours of post finishing work

Hi Superclodbuster, Thanks heaps for that. After reading that I think I will just print the whole body with windows and vinyl cut stickers to go over like everyone else is doing. Thanks for that. PS: Nice job on your builds.

me, i just hand painted it flat black with a brush. it was faster then trying to cut vinyl sheets and it doesn't peel off, you need to have a steady hand and a good brush. originally i spray painted but the masking took too long.
Tamiya paints make the job easy.

another work in progress FWD touring car of my design


Thanks heaps for that. I will take that approach. Wow looks like its going to be a nice car. Is that a ground up design? (Like did you design the whole thing). Just one small thing with the build as not 100% sure on parts. Is it GB02 with GB02 Gears or GB03 with GB02 gears. And is it 2 x GB02 / GB03 gear boxes? EG: one in front and one at rear of the same gear box? Hope that makes sense. Just want to make 100% sure before printing. This build really needs a PDF like the open RC F1 Car so the parts are known and of how many of them . (Just my suggestion for the owner if reading)

Front and rear is the same, so print two gearboxes. GB03 use the same gears as the old housing. On the details page you can see my update notes in chronological order, from the bottom up. The top update notes are the newest.

Hi tahustvedt thanks for that. Will do that when I get up to that stage. Cheers

Your second line - I wanted a monster truck that actually looks like a monster truck, and not a truggy with large wheels..... is exactly why I am making this! thank you! should be finished in a week or two.

Comments deleted.

Would this body fit on a HSP (FTX) V1 Outback?

Looking at modifying my crawler, and this body looks epic, and would suit the style i want to go for :)

I don't know. I have made the body with different wheelbases. You can find dimensions here:

Also check out my van body:

RC car scale pickup bodies.

i'm running into a strange issue. not sure if something got corrupted in the last update of the stl files.
i downloaded the most recent files because i switched computers and i needed to run out another set of axles.
the new axle that came out instantly started making popping sounds when i tested the new truck.
i tracked the problem to the upper counter gear between the bevel and the lower diff. there suddenly seems to be too much back lash between those gears and now the upper counter gear is skipping on the diff gear under load. i managed to force the gears to fail so i could see the issue clearly. i can see no movement between the top of the axle cover and the center section. i laid the parts in fusion 360 because i also want to beef up the mounting hardware that is cracking under stress from the walls being too thin for PLA. but if you could check the tolerances again on the axle case and counter gear and lower diff gear. the Bevel gears are fine.
I thought to splice the axle case and drop the countergear down .1-.2mm and see if it would be enough to tighten the backlash and stop the gears from skipping under load. I tried to tighten up the lower tolerance because i thought there was too much play in the lower diff bearing holders but that part is fine so i went back to the original tolerance.

i believe this is the issue Marcus24 is talking about in his post.

also i notice the top axle cover shape is odd for the bevel/input shaft it is elongated and not round and doesn't fit the curve profile of the center axle section, there is no play up and down with the countergear bearing and shaft but it looks like the cover is from a different version of the axle case, the curve of the bearing holder looks like the parts split was in the wrong spot(higher then it should be)

here is some screen caps from fusion 360 the gray is the top axle cover and the yellow the center section
you can see the odd shape of the top cover doesn't fit the center section profile and if i zoom on the bearing carriers for the counter gear you can see it oddly has 2 centers one higher one lower which might explain the backlash issue on the counter gear and the skipping issue that is now occurring



I haven't changed anything in ages.

The halves of the gearbox are not pefrect half circles, because that wouldn't work when printed. I made them slightly taller than half circles to compensate for overhang artifacts from gravity in the arch. There would be a huge gap between the halves otherwise. There's already a small gap as it is now.

well something changed i had an older version from when you just added the 03 Axle design going from the side to side assembly to the top down for strength and using the newest stl files i have the same issue that Marcus24 commented about. the difference with Marcus24 and me is i forced the gears to destruction so i could see the failure. the teeth are not engaging deep enough with each other under load and the tops of the diff gear teeth are snapping the tops off. all the bevel gears are fine and no problem with the input gear nor the diff gear bevels.
before destroying the gears i started to feel them by hand and there was more backlash then i would of liked between the diff and countergear which is why i suspected they were skipping on each other.

You can see the date by the files under the file tab. I haven't updated the files since last year. :)

last time i printed a truck out was last year. want to look into the gear mesh see if something isn't correct?

I will have a look. Too tired today though.

here is some photos same issue as marcus24

keep in mind this damage occurred with new PLA printed gears, brane new axle case, and i forced this damage with the truck on my bench sitting wheels up and i just gunned the throttle with no load just the weight of the tires, 2 teeth are folded over on the diff gear same contact area as Marcus. to me looks like 2 things the back lash/spacing changed somehow and is further apart and the 2 gears to my eye do not look like the profiles are the same. the counter gear looks to have a deep tooth profile compared to the diff gear. (different pressure angles and clearance distance) i had Gearotic do some weird mistakes on some gears i created, and i switched to opencad to double check on my projects. sometimes you get very different results with the same PA and pitch between programs and bump up one tooth and it fixes itself.
possible the diff gear is off by one tooth?

well started to mess around this evening. my software was having a problem generating a Pressure angle of 20 with 28 teeth Module 1 trying to match your clearance (backlash) it was making the software bug out. i guess you must of manually closed off the gear backspacing to add strength to the diff gear which is why the software refused to create the gear profile correctly.

well i decided to try out a 29T diff gear with pressure angle of 20 and module 1 with some backfill to strength the teeth, so i'm running it out and see if the mesh is too tight or not.

posted a quick gear fix, give it a try

Ursa 29T lower Diff Gear replacement

Cool. If the 29 tooth gear fits then it should be a good fix. The mesh is a little lose in CAD so the reason it skips is probably because the axles aren't round, but flat, so when they are on the flat side perpendicular to the gear line they give a little less mesh. Wrapping one layer of aluminum tape around the two drive axles to the wheels will probably tighten it up if the axles are loose in the bearings.

I will upload a test part for the gearbox housing that lowers the top bevel gear that contacts the diff gear by 0,4 mm. I think I made a mistake there which let the gear go up into the housing. The new part is Test01.stl

The 29T is working on the current axle there is just enough clearance to not have a major issue.
might not be a bad idea to have both options of a 28T or 29T diff gear so you can choose a tiny change in the final drive ratio LOL :-).

I adjusted the CV Joint by zxcvbn also. there was too much play in the original part for PLA printing. the input was wiggling bad.
that was causing the bevel gears to destruct.

finally the weather got nice so i could start doing testing again which is why the sudden influx of new issues.

I am working on a slightly beefed up axle case for PLA printing the amount of material around the bolt holes is too thin and the parts are Cracking just from the hardware sitting in the holes. so i beefed up the Diameter of the holes with 5mm and i moved out the 2 center axle case bolts to give more clearance and changed them from angled mounting to straight up and down.
the upper cover also needs a similar beef up.
here is a photo of the problem.

the Gold paint indicates a crack. same areas cracked on 2 different trucks.


the cracking occurred just sitting on the shelf over the winter as PLA acts like ABS under constant stress it cracks when the material is too thin in an area. Meshmixer also points this out in when analyzing a STL. if you want to beef up the axle on your end it will go faster since i'm working off the STLs. I also thought about 2 more Ribs underneath the axle input on the middle section of the axle to reduce some side to side flexing under load, set them at a 45 degree angle to the center rib. kind of like my battery holder chassis stiffener design

thin areas of the axle which are cracking

off to go break it again :-D.

Yes those cracks happen because of the gap I was talking about before, and is why I needed to make the bearing slots oval. Looks like I should have made them more oval on the main axle bearings. PLA will slowly deform when tension is put on it for a long time, and crack. It's hard to come up with a solution that works on every printer. :)

well the old Hill billy engineering solution works: keep adding stuff till it don't move or break :-D.

i know it is frustrating getting dragged back into an old project, i'm over a year into one of mine. but sometimes going back and working on it again gives you insight into your next project or another one where a similar solution can help it as well.

i think it is a great design and a good truck so worth the frustration.

I have problem with GB02-gears, I printed them from ABS and i used vaseline on them. They look strong enough.
In hands it moves nice without problem. On the car with motor it moves, but it makes noise and they are skipping. Gear teeths are ok, none is broken.
Any ideas where there may be a problem?

could be many reasons. first make sure the slipping is occurring where you think it is.

ABS shrinks more it could be possible the bevel gears are smaller then they should be. there could be too much play in the bevel shafts.
are the bearings putting correct side load on the differential, if the clearance is too loose then the diff can slip or pop bevels.
i made my Bevels out of 910 Taulman nylon. are the axle halves sitting tight together, if they have play in them the load can force the axle top and bottom to spread and cause the gears to pop or skip. Sometimes it might be a good idea to force destruction to find the problem.
run the truck until the gear fails then you can pinpoint he issue.

I reprinted all gearbox files with PET. I used GB03, GB02-input-onepiece, and GB02-gears. My printer is calibrated.
And it still skipping under load. I upload gear picture, part in red rectangle is skiping with the large differential gear.

see above your comment i reprinted a new truck and have the same issue

I used a 35T motor and a 3S 60-120C battery.

GB02-gears will continue to break.
(The gear teeth are broken.)

All parts were printed with 100% PLA.

I would like advice.

Less battery lol. 2s 35c will do that good. things break in 3s lol

either formula a stronger PLA Slicer sequence. less fan more fusion of layers. or if you are snapping off teeth then you need to move to ABS or Nylon filament instead of PLA.

i like to make the small bevel gears from 910 Taulman Nylon.

Try 2S battery or 55t motor instead. You can also print the gears in PETG for alittle more strength and elasticity. Always lubricate the gears with grease or they will break very quickly.

Thanks for sharing your design with us !
The link you provided for the 2S LiPo in the description seems to be wrong: it's actually a 3s lipo. What should I buy, a 2s or a 3s battery? For what I understand, if I chose to put a 3s LiPo instead of a 2s, the speed would be faster, but I will lose some torque. Am I right?

Thanks for letting me know about the mistake. Here's a battery that will work: https://www.banggood.com/Giant-Power-7_4V-6000mAh-2S-65C-Lipo-Battery-T-Plug-Hardcase-Pack-p-1080409.html?rmmds=search&cur_warehouse=CN

Other 2S hard case packs work too. 3S is pointless no this car.

I have a question about batteries. Did you use a couple of 3-cell battery packs in series or a pair of 6-cell batteries in parallel? It is similar in the case of LiPo batteries, right? That is, two packs 1S in series or two packs 2S in parallel?
I ask because according to the specifications of the ESC that you recommended, it supports up to 9 cells in NiMh or 3S in LiPo. So I estimate that I can not use two 6-cell NiMh in series or two 2S LiPo in series.
Is that so?

The regular frame supports a 6-cell ni-mh stick pack, or a 2S lipo hardcase battery.
The saddle pack frame supports saddle packs, which are either two 3 cell ni-mh in series, or two 1S lipos in series. One on each side.
There is no accomodation in the frames for more than this

Hi, I'm printing the model but I'm new to the RC.
Since I have to buy all the hardware, do you recommend me to use a brush motor or would it be better to use a brushless motor?
If it is preferable without brushes, what engine and ESC do you recommend?
Thank you very much.

i use a stock silver can 540 motor and it is way fast enough and has more then enough power to have a ton of fun.


i would recommend printing the small bevel gears, pinion gear, and wheel axles from taulman 910 nylon instead of PLA it will make the drive- line heat and shock resistant. there are many upgrades for the truck from other authors that will increase the trucks durability and performance.
i also recommend some type of heat break for the motor to reduce heat transfer to the PLA as it will melt.
a tamiya phonetic motor spacer is a good way to stop heat transfer.


I have melted the pinion gear which is why i went with 910 nylon as it absorbs heat no problem.

my trucks have tons of upgrades from thingiverse and also home brew to increase performance.

Brushless is superior to brushed, but brushed motors are more than adequate for this car, and cost less. It's difficult to find brushless motors that are "slow" enough for this truck. Most are too powerful to give reliable performance with the printed gear train. A 1000 to 1200 kv brushless motor would work well, if you can find one. Outrunners will work as long as they are the right diameter and have the right shaft size.

I still recommend the 35T motor in the parts list on the detail page.

Hi tahustvedt,

spring has finally sprung and i had a chance to beat on my Ursa with some new beefed up parts to the driveline.
I'm running zxcvbn CV joints now. i'm noticing stress cracks on all the 2mm bolt hardware around the new designed Axles( vertical cracks) from the hardware pulling the top and bottom axle case together. i think the axle wall around the 2mm hardware needs to be beefed up 1-2mm to compensate i'm using PLA. i noticed the same cracks on another Ursa truck that hasn't been run much so i think the cracks formed with the truck just sitting on the shelf over time. the parts have not failed yet but the cracks indicate not enough material to take up the stresses.

the new CVs work very well on the ursa truck. i have not tried the new Ball diff design that zxcvbn came up with.

I think I need to make the inside cavity around the bearings bigger so that the bolts don't stretch the housing when they are clamping down on the bearings.

the outer bolts by the steering pivots didn't have much pressure on them like the 2 center bolts for the bearing carriers but they cracked as well. i think Thin PLA under stress will crack like ABS. i figured beef up the thickness wall a little and see how it holds up.
if you open up the bearing carrier tolerance you have to be careful not to go too much as then the gears will hop under load.

right now with the cracks the axle housing is staying together. but i did see horizontal cracks forming in the center section.

I had a mauri big bear when I was a kid... I will never forget how many times my father was bringing home gear sets for it... lol.. excellent job on bringing an original back!

When the car moves, the screw (M4x20) is released from the wheel.
So I tighten it repeatedly.
Is there a workaround?

I used 4mm star washers they are like a spring washer to help keep the screws from getting loose.
You could also tack some crazy glue on the thread then install them to help lock them.

Wow!! I did not think that. applaud your idea. Thank you.

I will try it immediately.

another thing i did was i made the wheel axles from Taulman 910 nylon. PLA was too brittle when i really beat on the truck so nylon axles allowed flexibility from impact with the heavy tires on an object. the nylon shrank a good deal so i had to tap the 4mm screw hole after printing was completed. the shrink of the nylon and the tap left my wheel bolt very tight in addition i used the star washer, but i also had to go back and make my own wheel hex adapter to tighten the tolerance back up otherwise the PLA wheel hex slipped on the Nylon Axle Shaft.
no big deal just some quick work in Fusion 360 to get the revised parts out.

the small bevel gears in the axles and center gear case should be replaced with Nylon instead of PLA and i would recommend changing from the PLA filament for the Bevel gear shafts to 2mmx8mm Steel shafts. it takes extra work but you beef up the drivetrain.

print yourself a center skid plate also.

for fun i remixed some of the gears for use in a FWD i made. i may release it in the future.

Cubre diferencial central
by OzeAe

I couldn't find the recommend servo and its out of stock, is there an alternative servo that you also recommend?
I've found below servo and I don't know it will fit your design?


Please advice.


Do you have the original cad models you could post? I would love to try to convert this to nitro.

Sorry. I don't give away the originals for my designs.

Can you steer the four wheels with the 2 channels transmitter?

Yes. You need a y-cable to connect the two servos and a servo reverser for one of the servos. Here's a set with both included:

thanks for the info!

Comments deleted.

Please help me. TT

I bought the following parts.
DS-843 MG servo X2
540 Motor 60A ESC Carbon Brushed

I don't know how to connect the parts.

The parts you have bought are standard rc car components. I assume that people who build my cars know the basics already. The GT-2E comes with a receiver which communicates with the 60A ESC and servos via the three lead cables. The instructions should describe how.

You can ask about it in this thread, and post pictures if you like, and many will help you: https://www.rcgroups.com/forums/showthread.php?2883085-3D-Printed-monster-truck

Thank you. I will try again.

I have additional questions.

I don't know what difflock is for.

Where do I connect?

They go on each side of the diff gear instead of the small gears. That way the differential is eliminated for more grip on loose or slippery surfaces. for example snow.

Should glue be used to assemble motors and first CGB gear?

I don't use glue to install the gear on mine.

Comments deleted.

Hi, I enjoy your 3d printed truck and I want to print it but I want to know if any piece is more than 120120120mm?
And secondly can you make a video on your channel for make the truck ( you probably made the video I think but I don't saw it )
Thank you

scaling is all wrong what should the scale be set to?

This is a problem with your slicer.

Hello! I built one and the truth is great. I wanted to propose an improvement: are you capable of making a self-locking central differential? With a servo for example, to be able to lock it and unlocked from the radio transmitter.
You'll tell me what you think of the idea.

Hola! He costruido uno y la verdad que va genial. Quería proponerte una mejora: ¿serás capaz de hacer un diferencial central autoblocante? Con un servo por ejemplo, para poder bloquearlo y desbloqueado desde la emisora.
Ya me dirás que te parece la idea.

Hi, I have a problem with the rear or front gearbox. It "slips".
The differential gear miss gear with the upper one (the little one). In my case, I think the distance between those gears are too long.
Any Idea wath to do?

So cool!!! How fast can it go?

About 16-17 km/t with a Tamiya 380 motor and 20+ with a 540 35 turn motor.

Hi everyone one, I think that shaft01 goes in the GB03? Why there is a long and short shaft?

yes, Shaft01 goes inside the GB03 parts. shaft 01 is the Differential axle shafts.
there is a left and right because of the counter gear clearance and the diff sits off center.
look at the picture for the CG-02 diagram version for the shaft placement.

when you assemble you will see why they are different.

By the way, just a suggestion. Since the new GB03 is split horizontally into 3 parts, with the top part having the upper mount for the servo, would it be possible to add an option for mounting servos that are bigger than 23mm? Its quite difficult to source a micro servo with minimum 4kg torque that are 23mm in length (at least from where I am, took quite a while for the servos to arrive here from hobbyking). The only other option I saw was the Savox SH-0256 Servo (4.6kg), also not available here locally. haha

A bigger servo will hit the frame.

I see. Will a 3.5kg torque servo do? One of the corona servos i ordered seemed defective, I think I have to replace both so the two servos are the same. The 3.5kg torque servo is what we have locally.

By the way, I killed another set of input GB02. Everything worked fine. But after putting in some load (running the rc), it snapped after a few minutes. What am I doing wrong? Tried printing the one piece but the bearings are tight fit. The printed part got removed from the bed while fitting the bearing.

The frame04 (the very small one) works ok. Also, I have modified the frame03 by cutting a couple of rods so the servo can fit - it is also uploaded on the remix.

I have uploaded on the remixes a solution - a gearbox for use with standard size servo. Use at your own risk.

Completed everything and tried a first run. After a few minutes, both the input gear died (the shaft that goes inside the bevel gear was rounded). Maybe because I sanded the shaft to fit the bevel gear. I will try to reprint this and the one-piece input gear, and assemble it in the new GB03 housing. Wish me luck. haha

the tighter the fit the better, but you can also use some CA glue to hold the bevel on the shaft and keep it from wiggling and rounding out the hex on the shaft.

Also consider trying the one piece gear. You pause the print and add the bearings, and then the printer prints the shaft as one piece with the gear.

Tried the one piece. The bearings were a tight fit that I accidentally removed the print from the bed. Will try to remix to shave some mm from the shaft for easier fit.

The shaft is already 0,1 m undersize, at 11,9 mm, so the bearings should be a nice slip fit. Your printer is probably overextruding.

you should run some Dimension test pieces like a 20x20x20mm with 1mm Wall cube and see how off in the XYZ you are then adjust the printer or your slicer settings. you can compensate for tolerance issues and see if you are over extruding. it will show you the limits of your printer as well.

you could be over-extruding, Too hot, your multiplier could be wrong, etc.

Will have to check and re-calibrate my printer. But everything else i've printed on this project was a "perfect" fit. Most likely some of the settings were changed when I re-flashed Marlin to adjust the temps to accommodate nylon printing (for the gears).

Anyways, I've finished printing the remixed one piece I did and already assembled it. Will test later this evening. Thanks guys!

Ok. Tried another run and the one piece input seemed to work fine. My problem now is the servo steering (did front steering only as my other servo is failty). The steering servo does not turn fully both ways. After a few degrees of turn, it woild chatter or make slipping soinds. Any ideas why? Sorry, Im a noob when it comes to RC.

bad servo or your linkage is binding causing stress on the servo. is your servo saver setup and working correctly.

everyone has a different servo setup with this truck. the servo saver must be used, direct drive between the servo and steering linkage will cause failure.

when setup properly the wheels will just move a little bit when the truck is sitting still. under motion you will get full steering.
this is normal and wanted behavior.

Whats the maximum length of the 2S lipo batter that can fit with the printed shell?

138 mm will fit great. You can fit slightly longer packs by letting the body flex a little.

Just started the marathon task of printing. The large chassis side plates fit onto my CR10 so that's good. Many thanks for posting this, I just hope I can get it finished and running. If it works, I will have a go at designing a 1/14 crawler truck, preferably a 6x6 Oshkosh or similar. I've already done a few 1/16 tanks.

the axle shaft that clears the counter gear in the axle and has the little ridge to hold the bearing seems to be a weak point. the forces are so strong that the shaft is jamming into the bearing which wears away the little ridge. eventually the shaft cannot hold pressure against the diff bevel gears and then the transmission starts slipping. i didn't look into the clearances but a sleeve over the shaft that goes back to the diff bevel gear and fits between the bearing and the bevel gear would support it much better under load and prevent the axle diff from slipping.

Gotcha. I had made it smaller earlier on as a mistake. I made the ridge bigger and reuploaded the pindrive axles. I also uploaded a small file with just the one axle for you. temp.stl

really nice of you thanks :), have to start printing 4 of them for both trucks :D

Finally got the first test run of the new driveline and version 3 axle cases.

added a tamiya motor heat shield between the motor can and the PLA CGB housing to reduce melting of the PLA.
the heat shield is basically a plasticized paper to reduce heat transfer.

after melting a few pinion gears i also started making them from 910 Nylon.
the wheel axles i make from 910 Nylon as well.

will be modifying my steering setup as adding rear toe is a great idea for more straight stability.

Check out my new video testing the new frame with lower CG: https://youtu.be/CZGQl6PWfFM

awesome. :)
i just completed the second run with the second truck, so far so good.

It would be a good idea to hold the beveled gears (GB02input) in place, similar to the CGB with a colar or something.

Mine killed the bearings on the setup time. :)

I've split a couple of diff side gears since you updated them, I might try add a bit more meat to the back of them if there is room.
Never spilt a diff housing yet, they even survived the time a idiot sat on it and broke everything else.

Maybe they're coming out too tight on the shafts? That can split them as the tension forces will be incredibly high when the parts are forced together. Some PLA is too brittle for this and is unable to deform enough.

Always made sure there not to tight guess it's just the weakest part in the diff now. I printed everything in abs it's all I've ever used.

You might want to try PLA. PLA is 50% stronger than ABS.

Reinforced CGB for Ursa (bear) - Fully printable Monster Truck
by Saccco

sweet more printing to do!

started printing the new GB03 axle cases.

I decided with some of the overhangs and bridging to fully support them. so far got one set out clean up went easy.
it took me about 6.5 hours at .2 resolution 100% infill 210C degrees, i wanted good fusion of the PLA.

second set is running now. hope to start assembly today.

phew 20 hours printing just finishing up the first truck with all the new upgrades.

I'm going to try a hotter motor in my red truck now that I have printed pin drive axles. A 21t motor will make it able to jump well on my track... I think.

Those new axles are badass! :D

First download by me... :DD

Im building this project now and at around 80% of the printing. Im having trouble with the body. Im not sure if I can print it without support since there are details in the hood and rear part of the body. Im using Cura and am not sure if it can be done in cura. Any suggestions on how to do this.

you can do it without supports, it will actually come out much better. i will recommend a Large brim on the base i use a 6mm brim to make sure the body stays flat on the bed. my first tests were no brim and the corners were pulling up and bad warp-age started to occur

my first tests of the body were done with supports and they caused more trouble then they solved.

first get a bridge torture test STL so you can fine tune your printer and cooling needed.figure out the temperature for the material you are using
to get best results. i used hatchbox PLA at 205C with cooling 85-100% i run in an enclosure to help with layer bonding and shrinkage

here is one of my bodies running


you also do need to add a 100% fill layer where specified on the thing details readme. you have to go into the slicer software and force a 100% fill layer just under the grill for the front and just before the tailgate starts on the rear this is so the details have an attachment point for the bridging required. this is to keep the body shell as light as possible. you can also add 100% or higher fill areas using advanced slicer software settings to re-enforce areas around the body mounts or the roll cage.

i have 3 completed bodies under my belt and 2 tests i did for the front part that didn't work 100%

I printed all mine without support. Cura should be fine. Let the print finish even if it starts bending up towards the end. It will workj itself out before it gets to the top.

Printed without supports and adjusted my layer height to 0.4mm. Pretty satified with the result. Just waiting for the tires and off to assembly. Thanks man!

Is there a parts list on hardware? I start printing parts up but I don't have the screws or bearings.....so I need to go to the store to get them. I just was wondering if you had a list of hardware.

All hardware is listedon the main page.

started printing out the new shafts with pins.
I stripped out the rear shafts on one truck so Perfect timing.

Cool. I hope they work well. I haven't tried them yet. My printers are busy making buggy parts. cults3d.com/en/various/mkultra-3d-printable-1-10-4wd-buggy

I need to start printing that also :)

Comments deleted.

i just downloaded the newest version of the files and Difflock02.stl is not inside the files folder anything else missing?

I reuploaded it now.

I didn't see a difference with the center diff having newer bevels in the files list so I thought maybe because the spool version 2 was missing that the center diff didn't get an update listed in the readme.

It's a very complicated project and I'm on my own so it's hard to avoid mistakes.

yes it is and thank you again for designing it and publishing it :)

I'm making a second truck for a cousin so i wanted to get all the updates together for it during construction.

I made some CV joints for the diffs, I blew a diff gear up testing them in weekend. https://www.thingiverse.com/thing:2504465
and my shock mounts https://www.thingiverse.com/thing:2504477

CV joints for tahustvedt's Ursa (bear) - Fully printable Monster Truck
by zxcvbn
Shock mounts for tahustvedt's Ursa (bear) - Fully printable Monster Truck
by zxcvbn

Nice. I drew one just like it for my buggy, but never tested it. Great news that it works.

You should upload an assembled pic also. BTW good idea.

Will a servo with 2,2kg torque be enough?
I'm absolute newbie in this type of RC... :D

BTW Superb design!
Thank You!

It will steer ok when the truck is moving. It will really struggle to steer when the car is standing still though. I use 2,4 kg servos on one of my trucks and it works fine when the truck is moving. I recommend the Corona 843mg which is an 4,8 kg micro servo.

Thank you!
I'm trying to hold this in low budget. That's why I'm searching for alternative solution. :)
Maybe I'll get a bit bigger with modifications.

i've printed a tire with TPU Filament and a wheel with PLA. When i put the wheel Parts in the Tire until they snap in, there is a space between the parts from about 10mm in the middle and i can not screw the Rim together.i think one part of the wheel is to short a little?

The tire and wheels are an exact fit in the CAD. If there's 10mm between then something is wrong. Sounds like you put two inner wheel pieces together.

Here's a screenshot from the tire profile and whee parts:

ok that looks right....i am a little confused, but how can you explain this? ;)


i have not edited the files, only opened it in simplify3d and arranged.

Wow. I have no idea what happened here. I must have changed the wheel by accident. Sorry about that. I'll upload a second set of wheels for the printed tire. You don't have to print new tires.

Thanks! Nice to hear i have not wasted 100 grams TPU Filament ;-)
Can't wait to finish the Truck, only the wheels are still missing, love the design! :-)

Yeah that stuff is expensive, which is why I made both wide and narrow options available now. :)

I'm still in the process of putting my truck together but i got it running for the first time yesterday.
i'm working on the body right now and i noticed a slight problem with the Body02.stl, and body02-windows.
there are a few areas in the body where the model is too thin and you get holes when slicing the model.
on the body02 file the door panel gap lines at the bottom and bottom center cause holes in the slicer layers because they are too narrow.
I filled in a corrected model on my end thickening the bottom of the doors .5mm per side to stop the issue.
the body02 windows file has some more issues besides the same door gap issue it has some areas at the roof and top of the door frames being too thin and causing slicer issues. i noticed all this with .2mm layers.

i also beefed up the servo saver a little bit i felt the included hardware with the servo
could of been used better so i just changed the servo to arm mount making it a little bigger to use 2mm hex head bolts tied to the circular servo arm so you get a better stronger mount with minimal changes to the design

Use 0,4 mm extrusion width to print the body parts to save weight and avoid holes. The door lines will sltill have a couple of small gaps, but I left it like that because it's a door gap anyway, and hasn't given me any strength problems. The roof should not have any gaps when using 0,4 mm extrusion width.

I welcome any mods and remixes.

I went with the changes to the model, the extra .5mm per side thankfully fit my old NIMH 4000mill amp battery perfectly without stressing the sides of the body at all. I just finished the cab this morning took about 12 hours to print. should have it painted up and see if i have some decals laying around for it.

I was afraid my printer was going to have a bridging issue with the door gap and i didn't want to take a chance on such a long print to have it go wrong in the middle.


I love the truck thanks again for making it.

I'm going to test out the new servo saver the only change is to the base that attaches to the arm everything else is the same.
I added some spacers to the steering arms to move them out a little maybe i will make little PLA spacers to replace the extra 2mm nuts i'm using. if i works out well i'll see about posting a re-mix.

I want to try printing the tires with ninjaflex as well.

what is the pickup body

I put diff lockers in mine, I kept having problems with the front diff from to much wheel spinning as I drive it in a quarry. heaps better now for where I drive on fine lose rock.
I used a 540 45 turn motor with a 2s lipo and its still crazy fast, I should have gone with a 55 or 70 turn for where I use it.

Do you have the files for the tires? I would like to try to print some. Awesome design as well!!

I designed some printable tires now and uploaded them. They should print fine.

Awesome! Thanks! I can't wait to build this great design

Have started to assemble the diff's and found the axles are 0.6mm undersized where the bearings sit, I have added .6x4mm long where the bearing sits and made the flange the the bearing sits against on the long axle a little bigger
All other parts seem to be the right size.

Shocks turned up from BG, put one on and saw it wasn't going to work mounted to the top of the suspension arm, makes the arm twist from the offset load of the shock. Have made new mounts that clamp to the diff, they seem to be ok so far.

Might have another attempt of printing the body later with some new filament.

The axles are 0.2mm undersized by design at the bearing location, to fit the bearings easily. My printer makes them about 11.7 mm, which is 0.3 mm smaller than the bearing id. Your printer must be printing undersize for some reason to reduce the size an additional 0.3 mm. I do not think it will cause problems, however. Don't think it makes any difference.

Edit corrected a value.

Monster truck abuse and nudges from a tiger :) - I'm about 1/2 way through my build and have some Rigid Ink nylon 12 filament for my gears so will report my findings when I finally get to drive.

I've been looking into this some more and first of all, Hi neighbor!!! Saw that you're from Norway :)
What are the dimensions of it? Wheelbase and axle width are my main interests
If, when I start printing this, I find things i'd like to change, would you mind sharing the original files, they tend to be much easier to work with than stl files and of course you'll get full credit if I where to upload any changes

Sorry, I don't want to share the original Max files.

Axles are 11.9 mm, which fits 12mm bearings nicely when printed. Wheelbase is 290 mm with the long suspension. short suspension is 20 mm shorter on each end, and can be combined with long suspension for intermediate lengths.

I totally understand that, it must have been quite a task to get this together.

Awesome, about the dimensions I where hoping for, it should fit nicely among my other toys

This is so a must build, love it!!!
Out of curiosity, how much does it weigh?

Without battery, but Including everything else and some dirt::
-With the PVC Vampire Ghost body it weighs 1825 g.
-With the 3D printed pickup body it weighs 2085 g.

Awesome, the it should be able to float with the right tires

Hi there! I've begun printing, will start assembing as soon I finish.
A couple of questions:

  1. On Gears01, the gear with the bevel and the spur (to connect with GB-input) exists two times. Where is the second used?
  2. Why are the bearings used on pairs? One for each position, isn't enough?
    Also, I really love your bevel gears. Do you use a specific gear generator that I could use too?

And again, congratulations on the design.

Also, how does the motor pinion give power to GB-input?
Could you share with us the assembly multicolor (probably layered) 3d-model shown on an image?

GB-input is the shaft on the diff housings. It's not connected to the motor. The motor pinion drives the biggest spur in the center gearbox(CGB).

Have you downloaded the latest version of the files? There are two gears with the bevel and spur because there are two axle gearboxes (Print GB02 twice).

Using a single bearing on axles doesn't give enough stability and will cause premature gear and bearing wear.

Please read the assembly notes if you haven't already. I will upload more exploded views.

I generate gears using gearotic gear generator: http://www.gearotic.com/index.html

Yes, the new exploded views make that clear. Thank you.

Thanks you, your work is so amazing.

Im waiting for the bearing in my mail box and continue printing other parts

Very nice, I'm starting now to print it. Could you also upload the separate parts? I don't want to print all gears again because one of them didn't print well.

You should be able to do that yourself in the slicer. I have used Repetier Host and Simplify3d and both let you remove separate parts.

If I upload every little part by itself then it'll just be a horrible mess in the file list.

I didn't know that slicer could do that. Now that you said it, I found it. Thanks a lot!

I was in the process of designing a monster truck as well, ended up being more of a rock crawler that had issues. The redesign now has it being more of a stadium truck that uses the traxxas slash body.

I will have to print this and give it a shot, since it is a better design than my first truck.

Would be cool to see your design.

Here a picture of the original: http://i.imgur.com/osqIeHj.jpg

And this is the current one which is not done and I am waiting for parts. I went with a printed frame but bought drivetrain.

c66 stadium truck

Cool. Hope I have inspired you to continue. :)

The project was never stopped, just changed form and now is waiting on parts so I can get measurements for the wishbones. The joy of have printed and not printed stuff together.