Fully printable monster truck with four link suspension and four wheel drive and steering with three differentials. I wanted a monster truck that actually looks like a monster truck, and not a truggy with large wheels.
If you want to support my work you can use any of the Ebay or Banggood-links below before making purchases.
Mega truck wheels for it: https://cults3d.com/en/3d-model/various/mega-truck-tires-for-the-ursa-1-12-scale-monster-truck
High performance with the new drive train and axle housings:
New van body:
I made a new van body for it. get it here or here
I added a new roll bar with mounts for 22 mm LED light buckets
Added a new rollbar. Rollbar02.stl. Slightly easier to print and without lights.
New side frames are up now. They allow side mounting of the batteries and are ideal for saddle packs for a lower CG to reduce the chance of rolling over. They can also be used with two shorty packs in parallel or even two full size packs if you want insane duration.
The file name for the new frame is Option - Frame01-sidemount.STL
Added medium length suspension arms. These fall in between the existing short and long arms. The files are MidWB01 and 02. I like to use short length suspension in the front and medium length in the rear.
There was an error in the central gearbox housing. The new diff didn't fit. I have changed the the flattest side of the gearbox housing slightly to make room for the upgraded differential.
I added a new set of steering links with ball links for adjustment and separate front and rear steering cross links. The front part is the same length as the old links. The rear link is 1 mm longer to give some toe in in the rear end. The file name is Steeringlink03
Also new is a set of servo savers for the recommended servos. Servosaver02 is for the Corona while 03 is for servos with a larger 21 teeth flange.
Added mirrors and windshield wipers for the body. A little bit of detail make s a big difference. I uploaded a photo of the car with them installed.
I added new versions of all the drive shafts and hubs with holes and slots for a 2mmx13mm pin to increase the load capability and wear resistance of the rive couplings. The files start with "option - pindrives". Make the pins from 2mm piano wire or brass tubing. Make them 13 mm long. I haven't tried them myself yet, but pin drive works great with PLA in another project car other car.
Updated the center diff to the same stronger gear type as the axle gearboxes. Also updated the locking adapters for the diffs to fit the new diff style. Difflock02.stl
There was an error with the printable tire. It was wider than the wheel. I have uploaded Wheel02.STL which fits the printed tires. I also added new narrow tires which fit the original Wheels01.stl and take less elastomer to print.
Added left and right tires for those that want to try printing tires. They are designed to fit the rims,and should be printable.
I have uploaded new front and rear diffs. They use stronger and coarser gears. I have run my PLA version hard for a few times with no problems so it's definitely stronger than before. The updated file is GB02-gears.stl
New abuse video with a new lighter printed body. I printed it with 2% infill which saved 130 g. The rear diff now has two ABS bevel gears, which seems to hold up really well. I suspect ABS will be a good, cheap material for bevel gears.
A couple of abuse-videos. It has nylon (Taulman 910) bevel gears in the diffs here. 35t motor and 2S 6Ah lipo:
Added a special version of the GB02 input. It's a one piece part that requires that you pause the print between 22.2 mm and 23 mm and install both ball bearings before you continue the print. This creates a stronger part without gaps.
I made small changes to GB02-input and mating bevel gears (in gears01). If they break, the new parts have deeper gear mesh for higher strength.
Made slight changes to the lower suspension arms to improve the strength of the screw holes of the clamps. Also slight changes to the outside of GB02 for strength around the bottom area. Still compatible with the previous version.
Added split frame sides for small printers. Frame01-split01.stl and Frame01-split02.stl
Most of the parts have been changed recently, and I consider the design finished, so If you have downloaded parts earlier I recommend you download them again to get the latest versions. The drive train and spindles have all been upgraded.
I added two optional short suspension kits for shortening the wheelbase. Use in the front, rear or both as desired. Each kit shortens the wheelbase by 20 mm.
I uploaded shaft02.STL over again because there was a problem with the parts. The 3x19 mm rod wouldn't fit between the couplings.
I added a new axle gearbox assembly which uses a new input shaft which doesn't require carbon rods or filing of flats on the rods. It's easier to make and is stronger. It is uploaded as GB02.STL and GB02-input.STL. I also updated Shaft02.STL with a more robust design. Note that GB01 is still available, but I recommend the new version. The new version replaces two of the 3x7x3 mm bearings per axle for the same 12x18x4mm bearings used everywhere else.
Here's a video showing the performance with a 35T motor and lipos. I don't recommend runnign a lower turn than this. The photo showing the motor and pinion is taken after all my testing is done. The pinin shows no sign of use. Looks new. If you want to run higher turns that's fine:
I added a photo of the truck with a cool lexan body from Banggood.com. Also attached is a photo of body post drilling dimensions, and a photo of the frame without body. Check out the new video with the lexan body.
Changed "Frame03.STL" with an extra cross tube and also made small changed to "Spindle01.STL". Working on all the rive shafts now so new GB-housings, shafts and couplings will come up some time in the next few days.
I uploaded some stronger spindles and live axle housings with stronger spindle lugs.
I made a body for it as well tonight. It is based on a Tokyo Marui Big Bear Datsun body, with modifications to better fit this truck. It has been widened to fit over the batteries and has special body posts. I attached photos both without and with paint.
I appreciate any donations for my hard work and releasing for free, but only if you enjoy the model. ;)
Torture test video with lexan body:
-Tighten the suspension arm clamps around the axle balls untill they allow some movement, but not too tight. The ball joint needs to be able to move with suspension travel.
-The axle gearbox halves may have some uglyness in the top where the 7mm bearing goes. Just remove any excess plastic threads and stuff the bearing in there. I've done it to many units without failure. I might improve this part of the design later on.
-Apply a small amount of grease to the inside of all drive joints so that the plastic knuckles don't melt from friction. I use cheap bicycle lithium grease. Any grease will do.
-Apply grease to all gears. This prevents melting and keeps them working for long. I made closed gearboxes so that they could be greased without contamination. I use cheap bicycle lithium grease. Any grease will do.
-The drive shafts and drive knuckles can be a little tight. They will bed in.
-The gears will bed in if they feel rough in the beginning. Most of the gears seem to be very strong and show no signs of overloading. The differential bevel gears can break with very rough use if they are made from PLA. I eventually printed them from Taulman 910 nylon, which survived my torture tests.
-The smallest differential gears need small shafts to hold them in place. Make these short pieces from 1,75mm filament. Super easy and plenty strong with five shafts on total per diff.
-Ball bearings can be a tight fit, depending on how accurate your printer prints. The holes are designed slightly oversize. Just press them in there or carefully hammer with something that ensures the force hits the outside race. :)
-The lower links flex when the car rolls. This is by design and works well.
-Some parts have alternative parts so that the builder can create variations and change the look of the truck.
-The screws all thread into the plastic parts without any metal nuts. It may be difficult to screw them in the first time.
-Though the hardware list calls for machine screws, similarly sized self tapping screws will work fine in most cases. The exception being where the part is supposed to pivot on the screw, like the spindles and suspension link hinges. The length can also be different than the recommended in many cases as the holes are usually much deeper than necessary.
-The rear steering servo needs to be reversed. If it can not be reversed in the radio the longer servo link can be used instead by connecting to the top servo arm instead of the bottom.
-The diff lock gear is not recommended for jumps and high speed bashing because it increases the load on the whole drive train.
-GB02 is recommended, but if you for some reason still want to use GB01, here are instructions: On GB01 The input shaft on the live axle is made from 3mm carbon fiber rod. File flats on each end to fit in the gear and shaft joint and . The flats don't have to be perfect. Also apply CA glue to the flats when assembling. The gear ratio between the input and wheels is 5:1.
-Minimum 2 channel transmitter and receiver. This is the cheapest i can recommend
This is better because you can mix the steering in programming
-540 or 380 motor and ESC. The prototype uses a 21t GoolRC brushed motor for overload testing. I recommend a minimum of 35T
The best ESC for it is the Hobbywing Quicrun 80A "Crawler Brushed" ESC which can be set up to run with reduced brake and reduced punch which extends the gear life considerably: )
-Metal gear servos. Maximum 23mm body length. I use these
These also work well, but are a little weaker
-Six cell Sub-C ni-mh battery or 2S hard body lipo ( https://www.banggood.com/Giant-Power-7_4V-6000mAh-2S-65C-Lipo-Battery-T-Plug-Hardcase-Pack-p-1080409.html?p=HD240528697332015103), or saddle pack for the newest saddle frame (recommended).
-The springs are made from regular road bicycle tubes. Cut them as wide as you need to get the necessary tension. The butyl is very durable and won't rot. I used one of my old punctured tubes. I also use these rubber bands to hold the battery in place
-In addition to the printable body you can use other bodies. I ordered this body which fits well
-Four monster tires. I have not designed printable tires for it because it would take an absurd amount of rubber to make them and it's just so cheap for good tires. It probably takes less time to order and receive than it takes to print as well. :P I use the chevron version of the two in the following links
Or these tires
-7 3mmx19mm carbon fiber, steel or brass shafts for the diffs and live axle gearboxes
-2mm steel rod for the pin drive shafts and diff bevel gears
-4 to 8 3x7x3 ball bearings
-20 12x18x4 ball bearings. Search for "12x18x4 20pcs" on ebay for cheap bearings.
-44 M2x8 screws - differential gearbox assembly, upper four link clamp and steering link assembly. 24 of them for assembly of the two piece wheels.
-2 M2.5x22 screws - For mounting a 380 sie motor.
-22 M3x8 screws - Main frame assembly and steering spindle assembly.
-8 M3x12 screws - Lower suspension link and upper rubber band posts.
-6 M3x22 screws (M3x24 can also be used) - 540 Motor mount and lower rubber band posts.
-4 M4x20 screws - For the wheels.
Steeringlink01.STL - Steering links.
Steeringlink02.STL - Offset steering link for the servo saver.
Servosaver01.STL - Servo saver for installing onto the servo arm.
Bodypost01.STL - Shortest body post.
Bodypost02.STL - Body post.
Bodypost03.STL - Body post.
Bodypost04.STL - Body post.
Bodypost05.STL - Longest body post.
Bodypost05.STL - Body post for the rear of the Banggood Vampire Ghost Lexan body. Use file Body04.STL for the front posts for that body.
Suspension01.stl - Lower suspension links. Alternative 1. Choose the one you like.
Suspension02.stl - Lower suspension links. Alternative 2. Choose the one you like.
Suspension03.stl - Upper suspension links.
Suspension04.stl - Lower suspension bushing and rubber band flanges.
CGB-380.STL - Central gearbox and pinion for 380 size motors.
CGB-540.STL - Central gearbox and pinion for 540 size motors.
CGB-gears.STL - Central gearbox gears.
GB01.stl - Old version live axle gearbox housing.
GB01-input.stl - Input coupling and bevel gear for the old GB01 housing.
GB02.stl - New and improved version live axle gearbox housing.
GB02-gears.STL - GB02 gears.
GB02-input.stl - Input coupling and bevel gear for the new GB02 housing.
Difflock01.STL - Locking "gears" for the old style diff. Use if you want to lock the diff.
Difflock02.STL - Locking "gears" for the new stronger diffs.
Shaft01.STL - Live axle drive shafts
Shaft02.STL - Central drive shafts.
Spindle01.STL -Steering spindles.
Frame01.stl - Main frame sides.
Frame02.stl - Front and rear frame pieces. Alternative version 1.
Frame03.stl - Front and rear frame pieces. Alternative version 2.
Frame04.stl - Front and rear frame pieces. Alternative version 3.
Wheel01.stl - Monster truck wheel. Narrow type. Recommended for bought tires.
Wheel02.stl - Monster truck wheel. Wide type. Fits wide printed tires.
TireLeft.STL - Wide printable left tire. 83 mm width. Fits wide wheel.
TireRight.STL - Wide printable right tire. 83 mm width.Fits wide wheel.
TireLeft-narrow.STL - Narrow printable left tire. 73 mm width. Fits narrow wheel.
TireRight-narrow.STL - Narrow printable right tire. 73 mm width. Fits narrow wheel.
Body01.STL - The nose of the pickup body.
Body02.STL - The cabin of the pickup body.
Body03.STL - The bed of the pickup body.
Body04.STL - Posts with extra room for the thick printable body.
ShortWB01.STL - Suspension kit for shortening the wheelbase. option 1 arms.
ShortWB02.STL - Suspension kit for shortening the wheelbase. option 2 arms.