MakerBot Print is our newest print-prepration software, which supports native CAD files and STL assemblies,
allows you to interact with all your printers via the Cloud, and many other exciting new features.

Download Now

Recent Topics

List of Tronxy 3d printable modification/parts

by 3D_PrintSlav

A usefull list of usefull prints and modyfications for your Tronxy 3d printer:

Want to add more? Just write in post below and I add it when I see it.

Most if not all of those parts should work for all 3d printers from tronxy family unless specified otherwise

Part coolers:

  1. One of the best I found untill now. I have printed it in silver PLA and even tho its very thin it didnt melt when I was printing stuff in 245C

If you have bigger fan you want to use with it that might come helpfull:

  1. I used it for quite a while, its sturdy and works well however its pain in the donkey to remove it for maintenance. Also it have problems with printing in higher temp than 200C

  2. Looks like that might work for our Tronxy mashine as per this fb post (https://www.facebook.com/groups/1694483897515810/permalink/1826112524352946/)


  1. Its more or less garbage. I am putting it here because its my design, some people actually use this so they prob knows better how it works.

Belt Tentioners:

  1. X axis, very good, very reliable solution, rorks on my x1 and works on x3, I suspect it would work for any 3d printer with 20x20 open on one end axis.

  2. X Axis, another one, looks more sturdy, did not test it out actually.

  3. [x1] Y axis and some other improovements, did not printed out but looks sturdy:

  4. [x1] Y axis Not perfect but I have it on my printer for 9 months and it does work no problemo

  5. [x3] Y axis. Not sure how well it works as I dont have x3 but this fella does amazing job so I thing it will work perfectly fine.

Base case

1.[x1] A case for all electronic that goes underneath your printer, its good, you can print it on tronxy x1, a little bit of gluing and you might safe some pizza cartons to make bottom for it as it might be tricky to print bottom parts but its tested by me and works great

  1. [X1] Another one, looks better than previous one.

Small usefull thingos:

  1. Thumbnut screw replacement. For adjusting your bed level. Those are pure gold in comparison to metal ones that comes with the kit.

  2. 20x20 endstop fitting (its designed with z axis x1 in mind):


Tronxy X3 Supercooler - hot end fan shrouds
by idig3d
fan converter 30x30 to 40x40 for Tronxy supercooler
Tronxy X3 40MM Fan shroud
Ender 2 3D Cooling Fan Duct
by razer35
Tronxy x1 40 mm element cooling fan shroud
Tronxy X3 x-belt tensioner
by idig3d
TronXY X1 X-Axis Tensioner
Tronxy x1 belt tensioner for Y axis
Tronxy X3 y-belt tensioner (front)
by idig3d
TronXY X1 Modular Base
TronXY X1 V1 Control Box and base that can be printed on a X1
Endstop Holder for Tronxy x1 (or other 20x20 alu profile)
View Comment

Printer pauses repeatedly during print

by JDubya69

I was playing around with some of the custom Cura settings on my XY-2 Pro. Now, the print head pauses repeatedly during the print when it's on the perimeter. The only custom settings I have enabled are fan speed and ironing, and they're not checked. The print turns out OK, it's just VERY slow because of all the pausing.

View Comment

Z Axis Voltage Regulation (VREF) Calibration TronXY P8092M Melzi

by JBieri

I have a Melzi 2.0V5 on this TronXY P802M printer; I'm familiar with RAMPS 1.4, but the Melzi board is fresh to me. My NEMAs are 2.8V 1.68A according to the RepRap database (SL4STH40-1684A-23) and the VREF=(1.68)(8)(0.1)(0.9)=1.2096. I've set all of the trimpots to this and X,Y,E are slightly warm and sound correct, however, the two Z motors are VERY hot at idle (I know they stay on to maintain position) and share a controller. They sound low (grumbly), vibrate slightly, and kind of 'thunk' initially when power hits them. Too little voltage bc it's shared at the regulator (90% max from VREF calc is dropping to 45% to each)? How should I adjust? What have others done to solve this on this or similar machines (Anet, Prusa, +++)?

melzi melzi board nema17 nema17_stepper_motor P802m trimpot trimpots tronxy tronxy P802M Tronxy_P802
View Comment


by inakim

I have a couple of acrylics at home and I would like to manufacture the enclosure for the d01, does anyone have the original dimensions and mounting system? ....

View Comment

Tronxy XY-2pro

by MrAir23

Tronxy xy2 pro printer.
set the marlin.
how to install previous firmware.
thank you

View Comment