Hi all. I purchased a something called an EG4 XL which is an upgraded Tronxy X3S by a company out of Montreal, Canada.
Safer as I can get warranty and support, right? Lmao! Nope!
I know. Save it. I know better now! Lol
Zrib board with Ramps 1.4 and an ATmega2560 as the brains.
24volt 360w psu, pushing a 330 X 330 heated bed.
I really took my time to do it all right but when I started it up and tried to level the bed the hot bed turned on and all the white smoke that makes the mosfet work came wafting out within seconds. Shut off immediately.
I will go back over everything and make sure all is good. No shorts etc. Again!
But, what would the next step be if it was you?
Would you replace the 855nf mos with a better one? Replace the whole board? Throw the damn thing in the garbage and buy a different printer?
This is my first 3d printer but for the life of me I cant see the mosfet genie escaping for no reason. I just cant find the reason.
Any advice or answers to the above questions would be appreciated. Thanks.
We are using a IC-- MAX9926 from Maxim Integrated to filter 2 VR signals (from a HONDAS2000 Crank and Cam VR sensors) One being 24 tooth, and one being 3 tooth (per cycle of the Engine). At RPMs below approx 5000-6000 the signal comes through the 9926 fine, and triggers the MCU correctly such that it decodes it fine. At around this RPM we start to get extra/missing teeth on the IRQ lines to the MCU. Note we can 'push through' this noise and get to 9k RPM - just seems to be a 5-6K RPM issue...
MAX9926 Datasheet: http://www.kynix.com/uploadfiles/pdf2286/MAX9926UAEE2fV2b_13987.pdf
Well,We also used a scope to capture the signals at the entrance of the ECU to rule out electrical noise.
The signals are smooth and clear at both idle, AND when hitting the point the ECU loses sync due to the 'phantom' teeth. The scope doesen't show these phantom teeth so I am assuming it is a 9926 issue, or the parts R1, R2, C1, R3, R4, C26. The only difference between perfect idle signal and higher speed 'issue' signal is the frequency of the wave, and its amplitude, as shown in the plots. We have 50v P-P at high speed and around 20v P-P at low speed.
1) Maybe I should and how could I attenuate both signals say by half? (Adding what, where) 2) Should I reduce the value of C1/C26 as they might be acting as a filter?
With regard to (2) if I keep the throttle down and 'push through' the noise the engine will regain sync and run all the way to 9k RPM without issue, so that is also odd!
As a result,
Low speed, IRQs passed via 9926 so perfectly !
I have made a variable voltage power supply from an old computer atx, but as I am doing more precision electronics projects, I would Like to buy a Lab power supply.
I would like to spend about $100 - $150.
I would appreciate any advice before I buy one.
I'm wanting to purchase either :
12v 3a switches or
12v 5a switches (more expensive same thing)
To replace something similar to this :
Power switch -1 pc (rated 250V 1A, for mounting hole 13x19mm)
The fact that his power switch is rated 1a makes no sense to me. Does this mean my 3a switch model could replace this switch in the same build? Or should I stick with 5a like the psu will be rated? (I have 5a and 30a psus both of which I want to switch on and off).
I am very new to LED wiring in my 3D printing projects and need some advice on the one I am now attempting. Is this the correct forum to ask?
If yes, the pic roughly shows what I have and what I am attempting. Three strings of four LED bulbs that I want to wire through a switch and (hopefully) power with a 9V battery.